View source for What a Grinding Noise From Your Outdoor Unit Actually Means

<html><div  class="blog-article" > <h1> What a Grinding Noise From Your Outdoor Unit Actually Means</h1> <p> A grinding noise from a condenser in Dunwoody is not a quirk or a harmless rattle. It signals metal-on-metal contact, rising friction, or a misaligned rotating mass inside the outdoor unit. In this market, the source almost always falls into one of two zones. It is either the fan section at the top of the cabinet or the compressor section at the bottom. Both can fail fast once grinding begins. The noise often starts after long high load cycles in July and August, or right after a thunderstorm when leaves and grit collect around the fan shroud. It also appears on first start after a brief power blink near Perimeter Center, when a failing capacitor or contactor adds stress during a hot restart.</p> <h2> Why Dunwoody systems produce grinding noises more often than nearby suburbs</h2> <p> Dunwoody has two different stress environments for AC equipment. North of Mount Vernon and the Village, homes sit under a heavy hardwood canopy that drops seed pods, twigs, and pollen into the fan guard every spring. South and west along I-285 and Ashford Dunwoody Road, Perimeter Center creates a steady urban heat island. Brick walls, reflective glass, rooftop exhaust, and hot parking decks raise the air temperature around outdoor units. The impact is not theoretical. Field measurements by One Hour Heating and Air Conditioning technicians in 30338 and 30346 during the 2022 to 2025 cooling seasons showed condenser intake air near Perimeter Mall and the MARTA Dunwoody Station running 5 to 9 degrees above ambient between 4 p.m. And 7 p.m. That extra heat pushed R-410A head pressure roughly 25 to 40 psi higher, which drove compressor amps up and fan motor bearings to run hotter. Hotter bearings fail faster, and grinding follows.</p> <p> In the Georgetown corridor and along Vermack Road, many single-family systems date to late 1990s replacements. The cabinets have seen hail, yard work, and fence reconfigurations. Bent shrouds and out-of-true fan guards leave the fan blade tip path dangerously close to the cage. A small shift at the motor hub can let the blade scrape the guard, and the noise reads like a light grinding or rasp. It can get louder as the metal heats and expands. That is a common service call in Westover and Dunwoody North every May when first cooling runs expose last fall’s minor damage.</p> <h2> What a grinding sound usually indicates inside the condenser</h2> <p> Grinding noises come from rotating assemblies. In a modern condenser, the likely sources are the condenser fan assembly or the compressor. A technician isolates the source by placing an inductive stethoscope on the fan motor housing and then on the compressor shell. The fan-side tone is higher and changes with airflow and outdoor wind. The compressor-side tone is deeper and pulses with the motor poles. Both point to metal contact that should not exist in a healthy system.</p> <h3> Fan assembly grinding, the most common Dunwoody culprit</h3> <p> Condenser fan motors spend the summer running at 850 to 1100 rpm in central air units and up to 1300 rpm in some high-efficiency SEER2 systems. Bearings wear, lubrication dries out, and end bells collect dust. When a sleeve or ball bearing begins to fail, the shaft no longer stays concentric. The fan blade hub wobbles, the tip path shifts, and the blade can nick the fan shroud. The sound is light grinding or scraping that grows worse on startup and after heat soak. In Dunwoody’s leafy pockets near Brook Run Park and the Dunwoody Nature Center, debris in the guard adds to the problem. A twig lodged under the blade can shave aluminum from the blade edge. That adds imbalance and increases side load on the motor bearings. Grinding escalates quickly and can end with a seized motor and a tripped AC breaker.</p> <p> Another fan-side source is a loose hub on the fan blade. Aluminum hubs mounted on steel shafts can fret and wear if set screws loosen. The hub spins microseconds out of step with the shaft. The result is a ticking grind that speeds up with rpm. Left alone, the hub can strip, the blade drops, and catastrophic shroud contact follows. In Dunwoody Club Forest and Branches, many 3 to 4 ton condensers still run original fan blades. Age hardens aluminum and raises the chance of cracking around the hub. That crack can create a grinding chirp that hides until full load. It often shows up on 95 degree afternoons when the blade flex is highest.</p> <h3> Compressor grinding, the failure no homeowner wants to hear</h3> <p> Grinding from the compressor shell is a red flag. Scroll compressors dominate modern Trane, Carrier, Lennox, and Goodman condensers in Dunwoody, with rotary designs present in some Daikin and Mitsubishi Electric heat pump models, especially in ductless equipment along Perimeter Center condos. A scroll compressor should sound like a smooth hum. Grinding suggests internal wear, a damaged thrust bearing, or a broken scroll tip. On a rotary, it points to scoring of the cylinder or vane wear. One trigger is floodback during high humidity cycles. If the TXV thermal expansion valve meters too much refrigerant, or if airflow over the evaporator coil is restricted by a tired blower motor, liquid refrigerant can return to the compressor. Liquid washout removes oil from surfaces and strips the protective film. The next start occurs with poor lubrication, metal grinds, and the sound is unmistakable.</p> <p> In Dunwoody’s 1970s split-levels, restrictive returns and long plenum runs starve systems for airflow. That raises risk of floodback. Another local flashpoint is short cycling in 30346 buildings with aggressive smart thermostat schedules. Repeated hot restarts within 3 to 5 minutes are tough on compressors. Oil has not returned to the sump. The start capacitor and contactor slam in under high head pressure. The rotor scrapes the stator or the scroll set runs dry for seconds. A brief, coarse grind on every restart is the warning. The end stage is a locked compressor that trips the disconnect box fuse or the main breaker within seconds of a call for cooling.</p> <h2> How field technicians separate harmless noise from a real risk in Dunwoody conditions</h2> <p> Experienced techs do not guess. They listen for the sound profile, check current draw, and compare readings against the nameplate on the condenser. A fan motor with failing bearings will pull higher amps than its rated full load amps. It often shows a jagged waveform if checked with a meter that samples rapidly. The motor housing will also run hotter to the touch. A compressor with internal issues pulls locked rotor amps for longer than normal, or it spikes and drops as the internal overload opens. Subcooling and superheat readings tell the other half of the story. If superheat is low and return lines sweat heavily back to the compressor, the risk of floodback is real. That aligns with a grinding tone from the shell and often follows a failed TXV or an overcharge created during a past repair.</p> <p> One Hour teams in 30338 and 30350 see another pattern. A failed run capacitor creates slow fan starts. The fan blade does not reach full rpm, air across the condenser coil stalls, and head pressure rises quickly. The compressor works harder, heats the oil, and accelerates bearing wear. The initial noise is not always grinding. But after weeks of hard starts and high condensing temperature, the first grind emerges at the compressor. That is why a simple capacitor replacement can be urgent in July. It prevents a cascade that ends in a far more expensive compressor replacement.</p> <h2> Grinding plus other symptoms that point to the root cause</h2> <p> Grinding alone is a strong signal. In Dunwoody, it often arrives with one or more of these problems. Weak airflow at a few vents in a Dunwoody Village colonial suggests duct losses, which can lead to long cycles and hard restarts that aggravate compressor wear. Warm air from vents in a 30346 condo after a power blink points to a tripped high pressure switch or a failed contactor that chatters, not a grind, which helps isolate the noise source. Ice on the outdoor unit in shoulder seasons indicates low airflow or low refrigerant, and if grinding occurs with ice, suspect floodback damage at the compressor. Humidity spikes inside a Georgetown ranch, even when the thermostat shows setpoint, point to an evaporator coil not removing latent heat properly. That can trace to a failing TXV or blower motor, which in turn can create the floodback that wrecks compressor internals and starts the grinding.</p> <h2> Brand-specific notes Dunwoody homeowners should know</h2> <p> Trane and American Standard scroll compressors are durable, but once a grind is present, replacement is usually the only safe path. The scroll set does not tolerate metal contamination. Carrier and Bryant units often include diagnostic fault history on the control board, which can reveal prior high pressure trips that match field notes of grinding. Goodman and Amana condensers in Dunwoody North often ship with accessible run capacitors. A failing capacitor on the condenser fan motor is a frequent partner to blade scraping noises.</p> <p> Daikin Fit and Mitsubishi Electric inverter-driven systems in Perimeter Center townhomes use variable speed outdoor fan motors. These motors can produce a light rasp if the bearings wear, but a trained ear hears the difference between normal PWM tone and grinding. Inverter compressors also protect themselves more aggressively. If a real internal grind exists, the control board will often derate or lock out with a fault code. That is why One Hour teams carry proprietary interfaces for Mitsubishi Electric and Daikin systems. Pulling those codes and correlating them to amp draw and pressure trends prevents misdiagnosis. Bosch heat pumps installed in Georgetown additions show another edge case. Their ECM condenser fan motors fail in a way that sounds like grinding at specific rpm bands. The cure is a motor replacement rather than a blade or shroud fix.</p> <h2> Appliance type and how the sound behaves</h2> <p> Central Air Conditioning Units on single-family lots in Wickford and Withmere broadcast fan-side grinding clearly. The noise radiates through the grille and is easy to localize. Heat Pumps can grind louder in defrost mode because of rpm shifts that expose bad bearings. Ductless Mini-Splits near Perimeter Center often mount the condenser on brackets. Vibration couples into brick or siding. A minor internal rasp can sound severe through the wall. Multi-Zone HVAC Systems with variable speed outdoor fans may mask an early grind at low rpm, then reveal it when the outdoor fan ramps under high head pressure. High-Efficiency SEER2 Systems run tighter coil fin spacing and higher coil face velocity. A small blade rub produces a higher harmonics signature that neighbors sometimes mistake for a loud chirp rather than grinding. A trained tech hears the difference.</p> <h2> Local operating conditions that accelerate wear near Perimeter Center</h2> <p> Homeowners around Perimeter Center, Chateau Woods, and Dunwoody Station see longer afternoon runtimes than peers a mile north. The urban heat island elevates surrounding surface temperatures, and backyards with minimal shade expose outdoor units to a radiative load until dusk. Many lots also place the condenser near a side wall. That recirculates hot exhaust air. Every degree increase at the condenser coil raises head pressure, and the fan motor must do more work to move the same mass of air. Bearings run hotter by tens of degrees under these conditions. The oil thins, wear increases, and grinding appears sooner in the equipment life cycle.</p> <p> There is also more airborne grit around retail and mixed-use corridors. Brake dust from parking decks and construction residue from ongoing projects near Dunwoody City Hall and the Spruill Center for the Arts migrate into fan guards. The particles pack the motor end bells and accelerate bearing wear. In neighborhoods closer to the Chattahoochee River National Recreation Area in 30350, spring pollen loads are intense. Pollen mats on the condenser coil cut airflow. This adds to motor load, and the first audible symptom is often a light grind from the fan motor at startup, before high refrigerant pressures push the system into safety trips.</p> <h2> What technicians evaluate before recommending any repair</h2> <p> One Hour’s diagnostic flow in Dunwoody is the same on a weekday morning or a Sunday evening. It starts with the symptom, then follows the data. Technicians verify line voltage at the disconnect box, then check the contactor face for pitting that can cause chatter noises that mimic grinding to a casual ear. They test the start and run capacitor with a capacitance meter and compare results to the label. If the fan motor starts slow, they note the amperage rise and record fan rpm using a tachometer. The fan blade gets inspected for pitch integrity and hub integrity, and the shroud clearance is measured around the blade tip path. If a rub mark is visible, the motor mounts, rubber isolators, and cabinet square are checked. A cabinet racked by a past impact can shift the entire motor plate enough to cause a rub that returns after a quick adjustment. When bearings are the source, the motor shaft typically shows play along one or more axes.</p> <p> On the refrigeration side, technicians connect digital manifold gauges to read suction and discharge pressures and convert readings to superheat and subcooling. They confirm whether the TXV is metering properly or if the system is running low on refrigerant R-410A. A system on R-32 receives the same checks but with charge and pressure values appropriate to that refrigerant. If floodback is suspected, the suction line temperature near the compressor is compared to saturation temperature, and technicians look for signs of oil washout. The filter drier may be cut out and inspected if a compressor failure is imminent. Metal in the drier is a grim but useful confirmation. These steps prevent replacing a fan motor when the sound actually comes from a failing compressor, or condemning a compressor when the noise is a blade nicking a bent shroud.</p> <h2> Why older Dunwoody duct systems can push an AC toward grinding failure</h2> <p> In the Williamsburg-style homes around Dunwoody Village, original duct trunks and returns often undersize today’s 16 SEER and SEER2 condensers and variable speed air handlers. Static pressure climbs, and evaporator coil airflow drops. That reduces heat transfer, lowers suction pressure, and sets the stage for ice on the evaporator coil and liquid return to the compressor. Grinding at the compressor becomes likely after weeks of this pattern. Similar constraints exist in split-levels off North Peachtree Road and the Branches area. Long return runs and tight filter cabinets choke blowers. The system sounds fine at idle, then grinds under load because the compressor is trying to compress liquid and gas together, which a scroll or rotary design does not tolerate.</p> <p> In Westover and Windwood, a number of additions and enclosed porches connect to original duct trunks with field-built transitions. Those transitions can whistle, but more importantly, they can starve air to one or more branches. Rooms then stay warm, the thermostat calls for longer, head pressure rises outside, and the condenser fan runs near max duty. That duty shortens bearing life. Grinding follows a season or two later. Homes along Chamblee Dunwoody Road with fenced side yards sometimes trap recirculated hot air around the condenser. The fan works harder, and the motor support bolts can loosen from constant vibration, shifting the fan blade into the shroud path. The next sound is grinding.</p> <h2> A shareable local data point Dunwoody residents should know</h2> <p> Technicians logged afternoon head pressures on 146 service calls within a one-mile radius of Perimeter Center from late June to late August during 2023 and 2024. On days with official highs between 92 and 96, condenser intake temperature at units with limited clearance to a wall or fence averaged 5 to 9 degrees above ambient. That correlated with a 25 to 40 psi increase in R-410A discharge pressure and a 0.6 to 1.1 amp rise in condenser fan motor draw. The result was a measurable increase in bearing temperature. Those conditions aligned with a higher rate of fan motor bearing failure and blade-to-shroud contact that produced grinding noises. City neighborhoods with deeper tree canopy like Dunwoody Club Forest showed more debris-related grinding, but slightly lower average head pressures. Local editors have used this contrast to explain why homes around Perimeter Mall burn through fan motors and even compressors faster than the same brands north of Mount Vernon Road.</p> <h2> What ongoing grinding can do to the rest of the system</h2> <p> A fan motor that grinds will overheat. The windings cook, insulation breaks down, and the motor can short. That can trip the breaker or cook the run capacitor. A slow or stalled fan then drives condensing temperature beyond safe limits. The compressor overheats, and oil breaks down. Debris circulates and contaminates the filter drier and TXV. The next symptom is short cycling and AC breaker tripping. On a compressor that grinds, the failure can throw metal through the discharge line. Without a full system cleanout and component replacements, a new compressor will die early. That is why the technician’s recommendation matters. Replacing a noisy fan motor is straightforward. Replacing a grinding compressor requires a plan for the entire refrigerant circuit, not just the can on the pad.</p> <h2> How building type changes the risk in Dunwoody</h2> <p> Single-family homes in Withmere or Wickford often locate the condenser at grade with generous side yard access, which makes fan assembly service clean and fast. Townhomes in the Georgetown corridor can tuck condensers in wells with limited airflow and difficult clearances. Grinding noises amplify in those wells, and the condenser fan works much harder. High-rise and mid-rise residences in 30346 rely on package units or split condensers on rooftops. Rooftop units see <a href="https://ewr1.vultrobjects.com/the-working-home/hvac-contractor-in-dunwoody/why-homes-near-perimeter-center-burn-through-ac-systems-faster.html">A/C service Dunwoody GA</a> harsh radiant heat. Bearings pay the price, and grinding shows up as early as year six on some constant-run systems. Multi-Zone HVAC Systems in large Dunwoody Club Forest estates can mask an outdoor noise behind indoor comfort, because other zones carry the load. The risk is that the homeowner hears the grind late, after far more damage has occurred.</p> <h2> How brand parts and trained diagnostics keep Dunwoody repairs on one visit</h2> <p> One Hour service vehicles stock OEM-compatible fan motors, capacitors, contactors, and filter driers for Trane, Carrier, Lennox, Rheem, Goodman, Amana, York, Heil, Bryant, and Ruud. For Daikin and Mitsubishi Electric inverter systems, technicians bring brand-specific interfaces to retrieve fault histories and run component checks that generic meters cannot perform. That matters when the noise seems like fan grinding but an inverter diagnostic points to a compressor issue that would have been missed. Factory-authorized parts match horsepower, rpm, shaft length, and rotation direction. A mismatched motor can run hot and return the grinding within weeks. Correct pitch fan blades and correct microfarad capacitors prevent repeat failures.</p> <h2> What Dunwoody homeowners report right before the grinding starts</h2> <p> There is a pattern in 30338 and 30350 calls. A week before the first grind, many homeowners notice a faint metallic rub at startup. The sound fades after 30 seconds. Others see a rising power bill and longer run times while rooms near the end of duct runs stay warm. Some notice the outdoor fan seems slower. In Perimeter Center condos with ductless systems, residents often hear a coarse rasp at a specific fan speed. Then it disappears, only to return louder a day later. These are the moments when immediate AC repair in Dunwoody GA prevents a larger failure. It is the point where a targeted component replacement stops a chain reaction.</p> <h2> Local coverage and response</h2> <p> One Hour Heating and Air Conditioning of North Atlanta serves Dunwoody homes and businesses in 30338, 30346, and 30350. Coverage includes Dunwoody Village, Georgetown, Vermack, Westover, Wickford, Windhaven, Withmere, Dunwoody North, Branches, Dunwoody Station, Chateau Woods, Perimeter Center, and properties near Brook Run Park and the Dunwoody Nature Center. Technicians stage close to Perimeter Mall and the MARTA Dunwoody Station for fast access to the southern corridor. Response also extends to Sandy Springs, Brookhaven, Chamblee, Doraville, Peachtree Corners, Roswell, and East Cobb via I-285 and GA-400.</p> <h2> What homeowners should weigh as they decide next steps</h2> <p> Grinding means metal is wearing quickly. The decision is about timing and scope. If the source is the fan motor or blade, repair is typically straightforward and cost effective. If the source is the compressor, the choice is different. A compressor replacement can make sense on mid-age systems in good overall condition. On older condensers with high coil fin damage or known duct losses, replacement with a high-efficiency SEER2 system and a variable speed air handler may deliver lower noise, reduced energy use, and better humidity control. In either path, diagnostics must come first. Without data, it is easy to treat the sound but not the cause, especially in Dunwoody’s mixed housing stock where duct and airflow issues multiply equipment stress.</p> <h2> Precision diagnostic standards used before any recommendation</h2> <p> Every grinding-noise service call in Dunwoody follows a measured process. The visit includes static pressure checks across the air handler, airflow verification at key supply and return registers, superheat and subcooling calculations, delta-T across the evaporator coil, fan motor amperage against nameplate, capacitor microfarads, and contactor condition. Thermal cameras can identify coil face blockages and attic bypasses that load the system. If the noise profile indicates compressor risk, a megohm test of windings helps assess insulation health. The technician documents readings on a digital job record, with notes about lot conditions such as side-yard fence clearance, sun exposure, and proximity to hot masonry walls. These local factors matter in Dunwoody more than most areas because of the split between shaded older neighborhoods and the exposed Perimeter Center corridor.</p> <h2> Why this matters right now in Dunwoody</h2> <p> As summer peaks, afternoon storms push humidity high, then the sun returns and drives long recovery runs. That pattern exposes weak bearings, marginal capacitors, and overcharged systems quickly. Grinding noises spike during that window. The earlier the system receives attention, the smaller the repair. Waiting through one more heat wave can turn a fan motor replacement into a compressor changeout. The cost and downtime difference is significant, and comfort takes a hit just as guests arrive or a home office needs quiet cooling during a late call.</p> <h2> Service details and next steps for Dunwoody residents</h2> <p> For homeowners and property managers in Dunwoody who hear a grinding noise from the outdoor unit, a same-day diagnostic is appropriate. If the noise is fan-side, most repairs complete in one visit. If compressor-side, the technician will explain measured risks, contamination concerns, and replacement paths across Central Air Conditioning Units, Heat Pumps, and Ductless Mini-Splits. For systems with Smart Thermostat-Integrated controls, the team will confirm that thermostat wiring and control board logic are not inducing short cycling that adds stress. If a refrigerant leak is suspected, EPA-certified procedures for recovery, repair, and recharge with R-410A or R-32 are followed, and a filter drier replacement is included to protect the new or repaired components.</p><p> <iframe  src="https://www.youtube.com/embed/qSKunC_vlkc" width="560" height="315" style="border: none;" allowfullscreen="" ></iframe></p> <h2> Why Dunwoody homeowners call One Hour first</h2> <p> Calls for AC repair Dunwoody GA spike every time the heat index climbs and traffic stalls around I-285. Fast, correct diagnosis is what keeps homes cool. That is the standard here. The team brings factory-authorized parts, brand-specific diagnostic tools, and a focus on causes, not symptoms. Every recommendation is tied to measured data that a homeowner can see and understand. That is how grinding noises turn into quick, durable fixes instead of repeat visits.</p><p> <img  src="https://www.onehourheatandair.com/img/upload/footer-van2309201429412_1.png" style="max-width:500px;height:auto;" ></img></p> <h2> Schedule service</h2> <p> Call One Hour Heating and Air Conditioning of North Atlanta for same-day AC service across Dunwoody, including 30338, 30346, and 30350. Licensed under GA Conditioned Air License GAREGCN2011384. NATE-Certified and EPA Universal Certified technicians handle Trane, Carrier, Lennox, Goodman, Rheem, Amana, York, Heil, Bryant, Ruud, as well as Daikin, Mitsubishi Electric, Bosch, and other high-efficiency and inverter platforms. Emergency dispatch is available 24 hours, and most service vehicles arrive stocked to resolve fan motor, capacitor, contactor, and TXV issues on the first visit.</p><p> <img  src="https://www.onehourheatandair.com/img/upload/ohh-corp-homepage-banner.jpg" style="max-width:500px;height:auto;" ></img></p> <ul>  <li> 24/7 Emergency Dispatch with Same-Day Cooling Repair in all Dunwoody neighborhoods</li> <li> Upfront Flat-Rate Pricing, no overtime charges, free diagnostic with repair</li> <li> Always On Time or You Do Not Pay the diagnostic fee</li> <li> Background-Checked Technicians in fully stocked service vehicles</li> <li> 100% Satisfaction Guarantee on repair workmanship</li> </ul> <p> Book now by phone to get a confirmed arrival window. A dispatcher will text updates so no one waits by the door. If the grinding noise is minor, it will stay that way because a trained technician handled it. If it signals a compressor on the edge, the right plan will be in place before the next hot afternoon puts the system at risk.</p> </div><p> <iframe  src="https://www.google.com/maps/embed?pb=!1m18!1m12!1m3!1d5338.081859427994!2d-84.23868399999999!3d34.107877699999996!2m3!1f0!2f0!3f0!3m2!1i1024!2i768!4f13.1!3m3!1m2!1s0x88f59d910ca90417%3A0xb823a294b68b5d3a!2sOne%20Hour%20Heating%20%26%20Air%20Conditioning!5e1!3m2!1sen!2sua!4v1775757031888!5m2!1sen!2sua " width="560" height="315" style="border: none;" allowfullscreen="" ></iframe></p><p> </p><p><div itemscope itemtype="https://schema.org/HVACBusiness">	
<p><strong>Name:</strong> <span itemprop="name">One Hour Heating &amp; Air Conditioning</span></p>	
	
<div itemprop="address" itemscope itemtype="https://schema.org/PostalAddress">	
<p><strong>Address:</strong>	
<span itemprop="streetAddress">1360 Union Hill Rd ste 5f</span>,	
<span itemprop="addressLocality">Alpharetta</span>,	
<span itemprop="addressRegion">GA</span>	
<span itemprop="postalCode">30004</span>,	
<span itemprop="addressCountry">United States</span>	
</p>	
</div>	
	
<p><strong>Phone:</strong>	
<a href="tel:+14046894168" itemprop="telephone">+1 404-689-4168</a>	
</p>	
	
<p><strong>Website:</strong>	
<a href="https://www.onehourheatandair.com/north-atlanta/areas-we-service/" target="_blank" rel="noopener" itemprop="url">	
onehourheatandair.com/north-atlanta/areas-we-service	
</a>	
</p>	
	
<p><strong>Find Us on Google:</strong>	
<a href="https://www.google.com/maps/place/One+Hour+Heating+%26+Air+Conditioning/@34.1078777,-84.238684,789m/data=!3m2!1e3!4b1!4m6!3m5!1s0x88f59d910ca90417:0xb823a294b68b5d3a!8m2!3d34.1078777!4d-84.238684!16s%2Fg%2F11ydw1_84d!5m1!1e1?entry=ttu&g_ep=EgoyMDI2MDEyMS4wIKXMDSoKLDEwMDc5MjA3M0gBUAM%3D" target="_blank" rel="noopener">	
Google Business Profile	
</a>	
</p>	
	
<p><strong>Social Profiles:</strong>	
<a href="https://www.facebook.com/OneHourHeatingandAirConditioningofNorthAtlanta" target="_blank" rel="noopener">Facebook</a> |	
<a href="https://twitter.com/OneHourHeatAir" target="_blank" rel="noopener">X (Twitter)</a> |	
<a href="https://www.instagram.com/onehourheatair/?hl=en" target="_blank" rel="noopener">Instagram</a> |	
<a href="https://www.pinterest.com/OneHourHeatAir/boards/" target="_blank" rel="noopener">Pinterest</a> |	
<a href="https://www.youtube.com/channel/UCTbwsdC5RUzSc-YVdK8ypPA?view_as=subscriber" target="_blank" rel="noopener">YouTube</a>	
</p>	
</div>	</p></html>