View source for Furnace Not Heating: Thermocouple vs. Flame Sensor Issues 99042

<html><p> When a furnace refuses to heat, the temptation is to picture a catastrophic failure. In many homes, though, the problem comes down to a simple safeguarding part that either stopped sensing flame correctly or stopped telling the gas valve it was safe to stay open. On older standing-pilot furnaces, that part is the thermocouple. On modern direct-ignition furnaces, it is the flame sensor. Both exist to prevent burning gas without flame, but they work differently and fail in different ways. Distinguishing between them, and knowing how to respond, can spare you long nights in a cold house and save the price of an unnecessary service call.</p> <p> I have lost count of how many “furnace not heating” calls turned into a quick flame sensor cleaning or a thermocouple swap. At the same time, I have also seen homeowners spin their wheels on sensors when the root cause was airflow, low gas pressure, a dirty filter, or a control board fault. The trick is to read the sequence of operation and let the furnace tell you where it is getting stuck.</p> <h2> What each part does, and why it matters</h2> <p> A thermocouple is a small probe that sits in the pilot flame on standing-pilot furnaces. It generates a tiny millivolt current using the Seebeck effect when heated. That current holds a safety magnet in the gas valve. If the pilot goes out, the current drops, the magnet releases, and the gas valve closes. No flame, no gas. Thermocouples are passive and self-powered, which is why older furnaces could run without an external transformer or control board to keep the safety chain alive.</p> <p> A flame sensor lives on modern furnaces with intermittent pilot or hot-surface ignition. It is a metal rod that sits in the main burner flame. The control board applies a very small AC voltage to the rod and measures the microamp DC current that flows through the flame to ground through the burner assembly. Flame acts as a rectifier. If the board sees enough microamps, it knows a flame exists and keeps the gas valve open. If it does not, it shuts gas off and tries again or locks out.</p> <p> Both parts anchor the safety logic, but they fail in different ways. Thermocouples age and weaken, producing less millivoltage, or they get knocked out of the pilot flame. Flame sensors get coated in a thin layer of oxides and silica that insulate the rod, or they lose ground continuity through rusty burners. Once you know which device your furnace uses, you can connect the symptom to the likely cause much faster.</p> <h2> Know your furnace type</h2> <p> A standing-pilot furnace has a small, always-on pilot flame and a manual pilot control on the gas valve. If you have to press and hold a button while lighting a pilot with a match or piezo igniter, you have a thermocouple. A direct-ignition furnace uses a hot surface igniter or spark to light the burners on demand. You will see an igniter glow bright orange or hear rapid sparking on a call for heat. These systems rely on a flame sensor rod tied back to the control board.</p> <p> There is an in-between category: intermittent pilot. It lights a pilot with spark only when heat is needed, then verifies that the pilot lit before opening the main valve. Those systems may have a flame-sensing rod for the pilot and sometimes still use a thermocouple, but most residential units the past two decades rely on flame rectification to verify <a href="https://shed-wiki.win/index.php/Furnace_Not_Heating_Because_of_Return_Air_Problems:_Solutions">gas heater not working</a> flame.</p> <p> If you are unsure, remove the furnace door and watch the start-up sequence. Thermostat calls for heat, inducer comes on, pressure switch closes, igniter glows or spark begins, gas opens, flame lights, blower starts. Write down where it stops. That timeline is the roadmap.</p> <h2> The symptom map: how failures present</h2> <p> A thermocouple failure tends to show up as a pilot that lights only while you hold the button, then goes out when you release it. On some older valves, the pilot may stay lit for a few minutes then drop when the thermocouple cools or when the safeties cycle. It is a persistent, predictable symptom. The main burners may never light because the valve will not let them without a stable pilot.</p> <p> A dirty or failed flame sensor produces a different drama. The furnace goes through pre-ignition, the igniter glows, burners light with a smooth “whoomp,” and then three to ten seconds later, everything cuts out. The inducer keeps running, the board tries again, and you get two or three tries before a soft lockout. Some boards flash a “flame sensed” or “no flame” code. The blower may come on briefly with cold air if the fan-on delay passes before the board gives up.</p> <p> There are edge cases. Poor ground between the burner and board can mimic a bad flame sensor. A cracked hot-surface igniter can light the first time and fail the second, leading you to chase the wrong problem. Low gas pressure can light flame on one burner but not carry to the sensor, causing flame-sense failure even though gas is present. That is why the visual sequence is so useful.</p> <h2> Why sensors fail: the real-world causes</h2> <p> Thermocouples fail from age, heat cycling, and contamination. Over years, the junction just produces less millivoltage. If a water heater or furnace sits in a damp basement, corrosion can creep up the sheath. A thermocouple bent out of the pilot flame will show low output even if the pilot looks lit. Sometimes the issue is the gas valve magnet, not the thermocouple, but that is less common.</p> <p> Flame sensors fail from buildup. Combustion leaves a microscopic layer of oxides on the rod. Airborne contaminants add more: silicone from sealants, laundry products, aerosol cleaners, even a humidifier’s minerals. I have seen a brand-new furnace go into flame-sense fault within a few weeks in a remodeling project that used silicone caulk everywhere. The rod looked fine but read low microamps. Poor grounding also kills flame sense. The current must flow from the rod, through the flame, into the burner, through the cabinet, and back to the board. Rusted burner screws or a floating neutral can break that path.</p> <p> One more culprit deserves mention: airflow. Although airflow does not directly affect the flame sensor circuit, weak airflow overheats the heat exchanger and causes limit trips. The board may interpret timing as a flame failure if the sequence restarts. A “furnace not heating” call for sensor trouble sometimes turns into a dirty filter, matted evaporator coil, or blower failure. When a home also complains about ac not cooling in summer, that shared airflow restriction points right to the coil or filter. Maintenance on one affects the other, and both influence hvac system lifespan.</p> <h2> Hands-on checks you can do safely</h2> <p> Most homeowners can do some basic observation and cleaning without venturing into risky territory. Kill power to the furnace before you touch anything. Do not push on gas valves or bypass safeties. If you smell gas, stop and call a pro.</p> <ul>  Quick checks that often help: Replace or clean the air filter if it is dirty. A clogged filter stresses components, causes cycling, and shortens hvac system lifespan. Confirm the furnace switch is on and the breaker is not tripped. Make sure the thermostat is set to heat and demand is present. Look for diagnostic lights. Most boards flash a code that decodes on the door sticker. Inspect the flame sensor rod. If you can remove it with a single screw, gently clean the rod with a fine abrasive pad. Wipe off dust and re-seat it firmly to maintain ground. </ul> <p> That single list gives you a safe way to restore many flame-sense <a href="https://wiki-burner.win/index.php/Heater_Not_Working_After_Thermostat_Upgrade:_Compatibility_Tips">expert hvac repair</a> issues. For thermocouples, a homeowner can sometimes re-seat the tip in the pilot flame. If the pilot <a href="https://wiki-burner.win/index.php/AC_Not_Cooling_After_Thermostat_Replacement:_Common_Mistakes">what affects hvac system lifespan</a> still will not hold after a minute of heating and the tip is centered in the flame, the thermocouple likely needs replacement.</p> <h2> Reading the numbers: millivolts and microamps</h2> <p> Pros verify with instruments because the numbers tell the truth. A healthy thermocouple on a typical furnace generates around 25 to 35 millivolts open-circuit and can hold the magnet with at least 12 to 15 millivolts under load. If I measure 8 to 10 millivolts loaded, I expect nuisance dropouts. The flame look may be fine, but the power is not there. A marginal gas valve magnet can also demand more current than it should, so I isolate that by measuring open-circuit and closed-circuit readings.</p> <p> A flame sensor circuit measures in microamps DC. Most boards want 1.0 to 5.0 microamps. I see 2.5 to 4.0 microamps on a clean sensor with solid ground. If the meter shows 0.5 to 0.9 μA, the board will likely drop out after a few seconds. Cleaning the rod often bumps that number back into the safe zone. If it does not, I look at the burner ground path and the board’s sense circuit. A weak flame, misaligned burner, or delayed cross-lighting can also keep the flame from bathing the rod consistently.</p> <p> If you do not own a meter, observation substitutes. Count how many seconds from ignition to dropout. Note whether all burners light or only the first. A flame that lifts or wavers hints at low gas pressure or dirty ports. A flame that looks lazy and yellow points to restricted combustion air or a cracked heat exchanger, which is a safety concern that calls for professional evaluation.</p> <h2> Replacement parts and what to watch for</h2> <p> Thermocouples are inexpensive and standardized by length and thread. I carry 24, 30, and 36 inch models. If you replace one, route it the same way as the original so it does not touch hot surfaces or bind. Snug the connection into the gas valve, but do not overtighten. Position the tip in the upper third of the pilot flame where it is hottest. After replacement, light the pilot and hold the button for a full minute to heat-soak the junction before releasing.</p> <p> Flame sensors vary by shape and mounting bracket. Use the OEM part when possible, or a direct-match universal. The insulator must be intact, not cracked. When installing, make sure the rod sits in the heart of the burner flame, not off to the side. Tighten the retaining screw on clean metal to ensure ground. If the sensor wire is brittle or the spade connector is loose, replace or recrimp it. Routing the wire away from hot surfaces and ignition leads prevents false signals and premature failure.</p> <p> Hot surface igniters are fragile. If you see a white, hairline crack or the igniter does not glow, handle a new one by the ceramic base only. Do not touch the element. If an igniter was replaced recently and you are still getting flame-sense dropouts, remember, the igniter and sensor are separate. Cleaning the sensor is still required.</p> <h2> Edge cases that mimic sensor problems</h2> <p> Three service calls from the past few winters illustrate how symptoms can point you astray.</p> <p> A two-stage furnace would light on low fire and then drop out when it attempted to ramp to high fire. The first instinct was a dirty flame sensor. Cleaning helped briefly, then the same behavior returned. Manometer readings revealed low gas pressure on high fire due to a failing regulator. Flame became unstable and lost contact with the sensor. Fixing the gas supply resolved the issue.</p> <p> A 90 percent condensing furnace worked fine on dry days and failed on humid ones. The board flashed “no flame.” The flame sensor measured borderline microamps even after cleaning. The culprit turned out to be a partially restricted condensate trap that backed water into the collector box, affecting combustion air and flame shape. Cleaning the trap restored stable flame sense.</p> <p> A remodel introduced a new laundry room sharing the furnace room. Silicone caulk and dryer sheets filled the air. After that project, the heater not working calls started. Flame sensors were fouling every few weeks. We added combustion air from outdoors and advised against aerosol silicone use near the furnace. The problem disappeared. Contaminants matter, and the furnace breathes the same air you do.</p> <h2> Safety and when to call a pro</h2> <p> It is reasonable to clean a flame sensor or replace a thermocouple if you are comfortable, the gas smell is absent, and the furnace is otherwise in good shape. It is not reasonable to defeat safeties, jump out controls, or ignore repeated lockouts. If a furnace locks out after you have done basic cleaning, bring in a technician. They will check combustion, draft, gas pressure, venting, grounding, and control board logic. Those are not guesswork items.</p> <p> If the heat exchanger is cracked, flame rollout occurs, or the rollout switch trips, shut the system down. Flame appearing outside the burner box, scorching, or melted wiring are red flags. So is persistent yellow flame or soot. These conditions go beyond a sensor problem.</p> <h2> Maintenance that prevents repeat failures</h2> <p> Regular maintenance extends hvac system lifespan and reduces nuisance shutdowns. In practical terms, that means a yearly visit for a combustion check and cleaning on gas furnaces, and seasonal filter replacement. In homes with shedding pets or construction dust, filters clog faster. A high-efficiency media filter helps but must be sized correctly. Too restrictive a filter starves airflow and pushes the furnace into limit trips that look like intermittent faults.</p> <p> Keep return grilles open and supply registers unblocked. Vacuum the blower compartment annually. On condensing furnaces, flush the condensate trap. Ensure the vent and intake pipes are clear of leaves, snow, or nests. If your home has both a furnace and central air, remember that a dirty evaporator coil blocks airflow for both systems. When you hear about ac not cooling in July and furnace not heating in January, think shared restrictions.</p> <p> As for the flame sensor, the best practice is gentle cleaning during yearly service, not grinding it shiny. A light pass with a fine abrasive pad or steel wool is enough. Over-sanding thins the protective layer and shortens the sensor’s life. On pilot systems, confirm the pilot flame is sharp and blue, not lazy and yellow. Clean orifices if needed.</p> <h2> Balancing quick fixes with the bigger picture</h2> <p> It is satisfying to clean a sensor and bring heat roaring back, and it is often the right move. Still, I have learned to ask why a sensor got dirty in the first place. High humidity, contaminated air, weak flame, poor grounding, and venting issues all contribute. If a furnace needs sensor cleaning several times a season, treat that as a symptom, not the disease.</p> <a href="https://wiki-legion.win/index.php/How_Climate_Affects_Your_HVAC_System_Lifespan">local hvac system repair</a> <p> On older standing-pilot models, a thermocouple that fails every year can signal a pilot flame that is misaligned, a valve magnet that is weakening, or a draft that keeps snuffing the pilot. I have replaced thermocouples in drafty basements only to find a missing burner door or a vent connector with a backdraft. Fixing sheet metal and venting solved the real problem.</p> <p> When a system reaches the point where safety controls regularly trip, it is fair to discuss replacement. Not because the furnace cannot be repaired, but because reliability and safety matter in winter. A new sealed-combustion furnace with proper sizing, venting, and commissioning will run cleaner and with fewer nuisance calls, and will do more to preserve overall hvac system lifespan by matching airflow to the ductwork and indoor coil.</p> <h2> A quick decision guide you can trust</h2> <ul>  If the pilot will not stay lit unless you hold the button, think thermocouple. Verify the tip is in the pilot flame. If it is, replace the thermocouple. If burners light then shut off within a few seconds, think flame sensor. Clean the rod, check ground, and confirm the flame engulfs the sensor. If ignition never occurs and you do not see the igniter glow or hear spark, look upstream at limit switches, pressure switches, or the board, not the sensor. If the furnace cycles on limit or blows cool air, check airflow first: filter, blower, coil, and registers. If problems recur after cleaning or replacement, measure: microamps for flame sense, millivolts for thermocouples, gas pressure, and draft. Call a pro if you do not have the tools. </ul> <p> These steps cover most “heater not working” situations tied to sensors. The exceptions are where combustion, venting, or gas supply undermine the sensing process. Those require full diagnostic work.</p> <h2> The value of watching the sequence</h2> <p> Good troubleshooting respects the order of operations. A furnace is predictable when healthy. The more closely you watch what happens and when, the less you chase ghosts. I keep a mental stopwatch. Inducer starts, pressure switch closes within a second or two. Igniter glows in 15 to 30 seconds. Gas opens, flame lights in under five seconds. Flame proves within two to three seconds. Blower starts about 30 to 60 seconds after flame. Any delay or dropout pins the suspect stage. When the dropout is five seconds after flame, the flame sensor is a prime suspect. When it is immediate, look at cross-lighting of burners or igniter placement. When it happens minutes later, think limit and airflow.</p> <p> That habit also improves communication with your technician. If you can tell them exactly when shutdown occurs, what lights flash, and whether flame appears, they can arrive prepared with the right parts and save both of you time.</p> <h2> Final thought from the field</h2> <p> Sensors are the guardians, not the villains. They shut things down when the conditions are not right. If they get dirty, they are telling you about the combustion environment. If they weaken with age, they are asking for routine care. When a furnace is not heating, resist the urge to randomly replace parts. Let the sequence guide you, make the simple fixes, and respect the safety devices that keep your home safe. Clean flame, solid ground, steady airflow, and proper fuel pressure are the quiet essentials. Keep those in line, and the thermocouple and flame sensor will do their job in the background, where they belong.</p><p> </p><p>AirPro Heating & Cooling
<br>
Address: 102 Park Central Ct, Nicholasville, KY 40356
<br>
Phone: (859) 549-7341
<br>
<br>
<iframe src="https://www.google.com/maps/embed?pb=!1m18!1m12!1m3!1d174580.84128751408!2d-84.55795348374629!3d37.96900877020406!2m3!1f0!2f0!3f0!3m2!1i1024!2i768!4f13.1!3m3!1m2!1s0x88425991f2c8d667%3A0xd6a4fcd021fabe26!2sAirPro%20Heating%20%26%20Cooling!5e1!3m2!1sen!2sph!4v1762779271877!5m2!1sen!2sph" width="600" height="450" style="border:0;" allowfullscreen="" loading="lazy" referrerpolicy="no-referrer-when-downgrade"></iframe></p></html>