Setting up a brand-new shower system 67068

Installing a New Shower Unit

An effective shower setup needs careful planning and a great deal of work. For the most part, you will need to do 3 kinds of jobs: framing walls, installing the plumbing, and finishing walls.

Preparation

Firstly, you should choose the type of shower that you wish to install. It is important to establish whether the chosen shower can managing certain systems and can control a safe level of water through the boiler. Many shower systems nowadays are created to be versatile to different water pressures (such as saved hot water and cold mains).

It is likewise important to take into account the water pressure and the planning of the piping and drain for the shower

Different reliable plumbing services Kinds of Shower Units

Push-on Mixer: The hose pipe and spray parts of the push-on mixer shower unit can be connected to the bath tap based on your requirement, and the water emergency plumber near me temperature level can be adjusted via the taps. Push-on mixers are low-cost and very simple to set up. However, although the hose pipe connection is easy, it is quickly dislodged. Furthermore, it is troublesome to change the temperature level.

Bath/ Shower Mixer: The tube and spray of this kind of shower are combined with a bath mixer tap, and the temperature can be adjusted through the bath taps. It is a very cheap choice and no extra plumbing is involved. Nevertheless, the bath/shower mixers likewise suffer from bothersome temperature level control alternatives.

Manual Mixer: The hose and spray of a manual mixer shower unit are a professional plumbing service part of the wall system and the cold and hot water products are linked to a single valve The temperature and pressure of the water are controlled through either one or a variety of knobs (in more costly showers). Although temperature control is a lot easier in manual mixer types, they are more pricey than the formerly discussed mixers. They also need extra plumbing of hot and cold water system pipes.

Thermostatic Mixer: The pipe and spray of this shower type are a part of the wall system and the hot and cold water supplies are connected to a single valve here too. It is total with a built-in stabiliser to self-adjust the water temperature level and to prevent it from becoming too hot. One of the biggest benefits of a thermostatic mixer shower type consists of hassle-free temperature level control. However, it is the most costly of the various mixer choices.

Power Shower: A power shower is a single unit including an effective electrical pump that can changing both the water pressure and temperature level. This kind of shower can be fitted if there is supply of water from a cold water tank and a hot water cylinder. A power shower makes the modification of both pressure and temperature level easy. On the other hand, it is unsuitable for water heated up straight by the shower or where the water is supplied by a mix boiler under mains pressure.

Electric Shower: licensed plumbing company An electrical shower is plumbed into a mains cold water supply and it heats the water electrically. It is essential to note that for this shower type to be installed, the mains pressure requires to be at least 0.7 kg/sq cm (10lb/sq in). The unit permits the temperature and pressure to be changed via a knob. Models with temperature stabilisers are better as they stay unaffected by other taps somewhere else in use within the home. A significant downside of electric showers is that the control knob only enables the option of high temperatures at less pressure, or lower temperatures at a greater pressure. This is problematic in the winter when the spray is frequently weak and the mains water is chillier. Nevertheless, this issue is dealt with in some models which are available with a winter/summer setting.

Method

Depending on the type of shower you want to install, the shower head should either be suited order to prevent its contact with the water in the bath listed below or the base tray, or it needs to have a check valve.

Before starting, it is a good idea to mark the positions of the shower head and control, and to plan the pipe-work involved. Additionally, the drain system to eliminate the drainage will require to be planned. Both positions of the cable television route and the shower switch will also require to be thought about if a rapid or electrical shower system is being installed.

Use the direction guide provided with the shower unit to fit the shower control.

Before fitting the pipes that will supply the water to the shower system, it is very important to cut off the water system. In order to safeguard the pipelines, they need to be given a water resistant covering and also fitted with separating valves. The pipes can then be buried into the wall and plastered over to neaten the general look.

Fit the base tray, shower head, and fittings.

Connect the main shower control to the pipelines that will be supplying the water (This might require a female screw thread adapter).

Reconnect the supply of water and test the pipelines for any leakages, as some might need tightening.

If you are setting up an electrical shower, keep in mind to turn off the electrical power supply before making any electrical connections. When these connections have actually been made (there ought to be assistance within the user's manual), the power supply can be changed back on.

Adjusting Water Pressure to Fit Your Shower

The cold water reservoir can be lifted to a higher height (often just 150mm (6inches)) by fitting a strong wood support below it-- possibly composed of struts and blockboards. If you pick this alternative, the main and distribution pipelines will also need to be raised to satisfy the new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is selected, it must be connected into the power supply in order to operate.

Piping and Drainage

It is best to use 15mm size supply pipes, and make the runs to the shower as short and straight as possible so as to preserve maximum pressure and reduce heat loss. Additionally, by minimising the use of elbows for pipe corners, you can decrease the resistance in the circulation of the supply of water. You can achieve this by bending the pipes instead.

Most Common Mistakes

# Violating or disregarding regional code restrictions.

# Using pipes that are too small.

# Connecting copper to galvanized without utilizing a brass or dielectric fitting between the two.

# Not utilizing tape or pipe compound at threaded joints.

# Not leveling your components when setting up them.

# Not setting up an air space filling for fixtures.

# Cutting supply stub outs too short to install the shutoff valves onto after the completed wall remains in place.

# Not effectively aligning tubing into fittings or stop valves. (Requiring the nut onto the compression ring at an angle when the tubing is at an angle will cause a leakage.)

# When turning the water back on in your house, always run the outside hose pipe valve or flush your toilets to bleed dirt and air from the lines. This particles can trigger issues in your sink faucets and other pipes trim.