Setting up a new shower system 77346

Installing a New Shower Unit

An effective shower installation requires cautious planning and a lot of work. In most cases, you will require to do 3 kinds of jobs: framing walls, setting up the plumbing, and completing walls.

Preparation

Firstly, you need to decide on the type of shower that you want to set up. It is very important to determine whether the picked shower can managing particular systems and can regulate a safe level of water through the boiler. Many shower units nowadays are designed to be flexible to various water pressures (such as kept warm water and cold mains).

It is likewise crucial to consider the water pressure and the planning of the piping and drain for the shower

Different Kinds of Shower Units

Push-on Mixer: The hose and spray parts of the push-on mixer shower system can be connected to the bath tap according to your requirement, and the water temperature can be changed by means of the taps. Push-on mixers are inexpensive and very easy to set up. However, although the hose pipe connection is easy, it is quickly dislodged. In addition, it is inconvenient to adjust the temperature level.

Bath/ Shower Mixer: The hose pipe and spray of this kind of shower are combined with a bath mixer tap, and the temperature can be changed through the bath taps. It is an extremely cheap option and no additional plumbing is included. However, the bath/shower mixers likewise struggle with inconvenient temperature control choices.

Manual Mixer: The pipe and spray of a manual mixer shower system belong of the wall system and the hot and cold water supplies are linked to a single valve The temperature level and pressure of the water are controlled through either one or a range of knobs (in more costly showers). Although temperature level control is a lot easier in manual mixer types, they are more costly than the previously discussed mixers. They likewise need extra pipes of hot and cold supply of water pipes.

Thermostatic Mixer: The pipe and spray of this shower type belong of the wall unit and the hot and cold water materials are connected to a single valve here too. It is total with an integrated stabiliser qualified plumber near you to self-adjust the water temperature level and to prevent it from ending up being too hot. One of the greatest benefits of a thermostatic mixer shower type includes hassle-free temperature control. However, it is the most pricey of the different mixer options.

Power Shower: A power shower is a single unit including a powerful electrical pump that can modifying both the water pressure and temperature. This kind of shower can be fitted if there is water system from a cold water cistern and a warm water cylinder. A power shower makes the modification of both pressure and temperature simple. On the other hand, it disagrees for water heated up directly by the shower or where the water is supplied by a combination boiler under mains pressure.

Electric Shower: An emergency plumbing Mount Martha electric shower is plumbed into a mains cold water supply and it heats up the water electrically. It is necessary to note that for this shower type to be set up, the mains pressure needs to be a minimum of 0.7 kg/sq cm (10lb/sq in). The unit permits the temperature level and pressure to be changed through a knob. Designs with temperature level stabilisers are better as they stay untouched by other taps in other places in usage within the home. A major downside of electrical showers is that the control knob only enables the alternative of high temperatures at less pressure, or lower temperature levels at a higher pressure. This is problematic in the winter when the spray is typically weak and the mains water is cooler. Nevertheless, this issue is dealt with in some designs which are offered with a winter/summer setting.

Method

Depending on the type of shower you wish to set up, the shower head need to either be suited order to prevent its contact with the water in the bath below or the base tray, or it must have a check valve.

Before starting, it is recommended to mark the positions of the shower head and control, and to prepare the pipe-work involved. In addition, the drain system to remove the waste water will require to be planned. Both positions of the cable television path and the shower switch will also need to be thought about if an instant or electrical shower unit is being installed.

Use the direction guide supplied with the shower system to fit the shower control.

Before fitting the pipes that will supply the water to the shower system, it is essential to cut off the water supply. In order to safeguard the pipelines, they should be given a waterproof covering and likewise fitted with separating valves. The pipes can then be buried into the wall and plastered over to neaten the total look.

Fit the base tray, shower head, and fittings.

Connect the primary shower control to the pipelines that will be providing the water (This may require a female screw thread adapter).

Reconnect the supply of water and test the pipelines for any leakages, as some may need tightening.

If you are installing an electrical shower, remember to turn off the electrical power supply before making any electrical connections. As soon as these connections have been made (there need to be assistance within the instruction manual), the power supply can be switched back on.

Adjusting Water Pressure to Fit Your Shower

The cold water tank can be raised to a greater height (sometimes as little as 150mm (6inches)) by fitting a strong wooden assistance underneath it-- possibly made up of struts and blockboards. If you choose this choice, the primary and distribution pipes will likewise need to be raised to fulfill the brand-new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is selected, it needs to be connected into the power supply in order to operate.

Piping and Drainage

It is best to utilize 15mm size supply pipes, and make the go to the shower as brief and straight as possible so regarding preserve maximum pressure and minimise heat loss. Additionally, by reducing using elbows for pipeline corners, you can reduce the resistance in the circulation of the water system. You can achieve this by bending the pipes instead.

Most Common Mistakes

# Violating or neglecting local code restrictions.

# Using pipelines that are too small.

# Attaching copper to galvanized without utilizing a brass or dielectric fitting in between the two.

# Not utilizing tape or pipeline substance at threaded joints.

# Not leveling your components when installing them.

# Not installing an air gap filling for fixtures.

# Cutting supply stub outs too brief to set up the shutoff valves onto after the finished wall is in place.

# Not effectively lining up tubing into fittings or stop valves. (Forcing the nut onto the compression ring at an angle when the tubing is at an angle will trigger a leakage.)

# When turning the water back on in your house, always run the outdoors tube valve or flush your toilets to bleed dirt and air from the lines. This debris can trigger issues in your sink faucets and other plumbing trim.