Installing a new shower system 37718

Installing a New Shower Unit

An effective shower installation needs careful preparation and a great deal of work. In many cases, you will require to do 3 kinds of jobs: framing walls, installing the plumbing, and ending up walls.

Preparation

Firstly, you need to choose the kind of shower that you wish to set up. It is necessary to establish whether the selected shower can managing particular systems and can manage a safe level of water through the boiler. Most shower units nowadays are developed to be flexible to various water pressures (such as saved hot water and cold mains).

It is likewise crucial to consider the water pressure and the planning of the piping and drainage for the shower

Different Kinds of Shower Units

Push-on Mixer: The pipe and spray parts of the push-on mixer shower system can be linked to the bath tap based on your requirement, and the water temperature level can be adjusted via the taps. Push-on mixers are low-cost and exceptionally easy to install. However, although the hose connection is easy, it is easily removed. Furthermore, it is troublesome to change the temperature level.

Bath/ Shower Mixer: The hose pipe and spray of this type of shower are integrated with a bath mixer tap, and the temperature level can be adjusted through the bath taps. It is a really inexpensive choice and no extra plumbing is included. Nevertheless, the bath/shower mixers likewise suffer from bothersome temperature control alternatives.

Manual Mixer: The tube and spray of a manual mixer shower unit belong of the wall system and the cold and hot water products are connected to a single valve The temperature level and pressure of the water are controlled through either one or a range of trusted plumber Dandenong knobs (in more pricey showers). Although temperature level control is a lot easier in manual mixer types, they are more expensive than the previously discussed mixers. They likewise need extra plumbing of cold and hot water supply pipes.

Thermostatic Mixer: The hose and spray of this shower type belong of the wall system and the hot and cold water materials are connected to a single valve here too. It is total with an integrated stabiliser to self-adjust the water temperature level and to avoid it from becoming too hot. One of the greatest advantages of a thermostatic mixer shower type consists of convenient temperature level control. However, it is the most pricey of the various mixer choices.

Power Shower: A power shower is a single unit including a powerful electric pump that can changing both the water pressure and temperature. This type of shower can be fitted if there is water system from a cold water tank and a hot water cylinder. A power shower makes the modification of both pressure and temperature simple. On the other hand, it disagrees for water warmed straight by the shower or where the water is provided by a combination boiler under mains pressure.

Electric Shower: An electrical shower is plumbed into a mains cold water supply and it heats the water electrically. It is very important to keep in mind that for this shower type to be set up, the mains pressure requires to be at least 0.7 kg/sq cm (10lb/sq in). The system permits the temperature and pressure to be adjusted through a knob. Designs with temperature level stabilisers are better as they stay unaffected by other taps in other places in usage within the home. A significant downside of electric showers is that the control knob only enables the alternative of high temperatures at less pressure, or lower temperatures at a higher pressure. This is problematic in the winter when the spray is often weak and the mains water is chillier. Nevertheless, this issue is tackled in some designs which are available with a winter/summer setting. reliable plumber in Mount Martha

Method

Depending on the type of shower you want to install, the shower head must either be fitted in order to avoid its contact with the water in the bath below or the base tray, or it should have a check valve.

Before starting, it is advisable to mark the positions of the shower head and control, and to plan the pipe-work included. Additionally, the drainage system to eliminate the waste water will need to be prepared. Both positions of the cable television path and the shower switch will also need to be thought about if an instant or electrical shower system is being installed.

Use the guideline guide offered with the shower system to fit the shower control.

Before fitting the pipelines that will supply the water to the shower system, it is very important to cut off the water system. In order to safeguard the pipes, they need to be given a waterproof covering and likewise fitted with separating valves. The pipes can then be buried into the wall and plastered over to neaten the general look.

Fit the base tray, shower head, and fittings.

Connect the primary shower control to the pipelines that will be providing the water (This may need a female screw thread adapter).

Reconnect the water supply and test the pipes for any leakages, as some might need tightening.

If you are setting up an electrical shower, keep in mind to turn off the electrical power supply before making any electrical connections. As soon as these connections have actually been made (there need to be assistance within the instruction manual), the power supply can be switched back on.

Adjusting Water Pressure to Match Your Shower

The cold water reservoir can be raised to a higher height (sometimes as low as 150mm (6inches)) by fitting a strong wooden assistance below it-- potentially made up of struts and blockboards. If you choose this choice, the primary and circulation pipelines will likewise have to be raised to fulfill the brand-new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is picked, it should be connected into the power supply in order to operate.

Piping and Drainage

It is best to utilize 15mm size supply pipes, and make the go to the shower as short and straight as possible so regarding preserve maximum pressure and reduce heat loss. In addition, by reducing making use of elbows for pipeline corners, you can decrease the resistance in the circulation of the water supply. You can accomplish this by flexing the pipes instead.

Most Common Mistakes

# Breaching or ignoring regional code restrictions.

# Using pipelines that are too small.

# Connecting copper to galvanized without using a brass or dielectric fitting between the two.

# Not using tape or pipe compound at threaded joints.

# Not leveling your components when installing them.

# Not setting up an air gap filling for fixtures.

# Cutting supply stub outs too short to install the shutoff valves onto after the ended up wall is in place.

# Not correctly aligning tubing into fittings or stop valves. (Forcing the nut onto the compression ring at an angle when the tubing is at an angle will cause a leakage.)

# When turning the water back on in your home, always run the outdoors tube valve or flush your toilets to bleed dirt and air from the lines. This particles can cause problems in your sink faucets and other plumbing trim.