Installing a brand-new shower system 26372

Setting Up a New Shower Unit

A successful shower setup needs careful preparation and a great deal of work. Most of the times, you will need to do 3 kinds of tasks: framing walls, setting up the pipes, and ending up walls.

Preparation

Firstly, you need to decide on the type of shower that you wish to set up. It is very important to establish whether the picked shower is capable of dealing with particular systems and can control a safe level of water through the boiler. Most shower systems best plumbing services company nowadays are developed to be flexible to various water pressures (such as stored hot water and cold mains).

It is also crucial to take into account the water pressure and the preparation of the piping and drainage for the shower

Different Kinds of Shower Units

Push-on Mixer: The hose pipe and spray parts of the push-on mixer shower unit can be connected to the bath tap according to your requirement, and the water temperature can be adjusted through the taps. Push-on mixers are inexpensive and very simple to set up. Nevertheless, although the tube connection is basic, it is easily removed. Additionally, it is inconvenient to change the temperature.

Bath/ Shower Mixer: The pipe and spray of this kind of shower are integrated with a bath mixer tap, and the temperature level can be adjusted through the bath taps. It is a really low-cost choice and no additional plumbing is involved. However, the bath/shower mixers likewise experience troublesome temperature level control alternatives.

Manual Mixer: The tube and spray of a manual mixer shower unit are a part of the wall system and the hot and cold water materials are connected to a single valve The temperature level and pressure of the water are managed through either one or a variety of knobs (in more pricey showers). Although temperature level control is a lot easier in manual mixer types, they are more pricey than the formerly pointed out mixers. They also require additional pipes of cold and hot supply of water pipes.

Thermostatic Mixer: The pipe and spray of this shower type belong of the wall unit and the hot and cold water products are connected to a single valve here too. It is total with an integrated stabiliser to self-adjust the water temperature level and to avoid it from ending up being too hot. Among the biggest advantages of a thermostatic mixer shower type includes practical temperature control. Nevertheless, it is the most costly of the various mixer options.

Power Shower: A power shower is a single system including a powerful electrical pump that is capable of altering both the water pressure and temperature. This kind of shower can be fitted if there is water supply from a cold water tank and a hot water cylinder. A power shower makes the change of both pressure and temperature easy. On the other hand, it is unsuitable for water warmed directly by the shower or where the water is provided by a combination boiler under mains pressure.

Electric Shower: An electrical shower is plumbed into a mains cold water supply and it warms the water electrically. It is very important to keep in mind that for this shower type to be set up, the mains pressure needs to be a minimum of 0.7 kg/sq cm (10lb/sq in). The system allows the temperature and pressure to be adjusted by means of a knob. Models with temperature stabilisers are much better as they stay unaffected by other taps elsewhere in use within the household. A major disadvantage of electrical showers is that the control knob just permits the option of high temperatures at less pressure, or lower temperature levels at a greater pressure. This is bothersome in the winter when the spray is often weak and the mains water is cooler. Nevertheless, this problem is taken on in some models which are readily available with a winter/summer setting.

Method

Depending on the kind of shower you want to install, the shower head need to either be suited order to avoid its contact with the water in the bath listed below or the base tray, or it needs to have a check valve.

Before beginning, it is recommended to mark the positions of the shower head and control, and to plan the pipe-work involved. In addition, the drain system to remove the drainage will require to be prepared. Both positions of the cable route and the shower switch will likewise need to be considered if an instantaneous or electrical shower unit is being installed.

Use the guideline guide offered with the shower unit to fit the shower control.

Before fitting the pipelines that will supply the water to the shower system, it is essential to cut off the supply of water. In order to protect the pipes, they should be provided a waterproof covering and likewise fitted with isolating valves. The pipes can then be buried into the wall and plastered over to neaten the total look.

Fit the base tray, shower head, and fittings.

Connect the primary shower control to the pipes that will be supplying the water (This may require a female screw thread adapter).

Reconnect the supply of water and test the pipelines for any leaks, as some might need tightening.

If you are installing an electrical shower, remember to turn off the electrical energy supply before making any electrical connections. As soon as these connections have been made (there need to be assistance within the user's manual), the power supply can be changed back on.

Adjusting Water Pressure to Suit Your Shower

The cold water reservoir can be raised to a greater height (often as local best plumbing company little as 150mm (6inches)) by fitting a strong wooden assistance below it-- potentially composed of struts and blockboards. If you choose this option, the primary and circulation pipes will likewise need to be raised to meet the brand-new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is selected, it should be linked into the power supply in order to operate.

Piping and Drainage

It is best to use 15mm diameter supply pipelines, and leading plumbing company make the go to the shower as brief and straight as possible so regarding keep maximum pressure and minimise heat loss. Additionally, by minimising using elbows for pipe corners, you can decrease the resistance in the flow of the supply of water. You can attain this by affordable best plumber bending the pipelines instead.

Most Common Mistakes

# Violating or neglecting regional code restrictions.

# affordable top plumbers Using pipelines that are too small.

# Connecting copper to galvanized without using a brass or dielectric fitting in between the two.

# Not utilizing tape or pipe compound at threaded joints.

# Not leveling your components when installing them.

# Not setting up an air space filling for fixtures.

# Cutting supply stub outs too brief to set up the shutoff valves onto after the ended up wall is in place.

# Not effectively aligning tubing into fittings or stop valves. (Forcing the nut onto the compression ring at an angle when the tubing is at an angle will cause a leak.)

# When turning the water back on in your home, always run the outside hose pipe valve or flush your toilets to bleed dirt and air from the lines. This particles can cause problems in your sink faucets and other plumbing trim.